Family Truckster

[GUNGUY-TC]

I'm new here so thought I would post the truck I just bought a few weeks back to get started. I have been looking at other builds on here and figured I need a project.

 

[GUNGUY-TC]

Starting the DEMO

The back end wasn't very well put together so I started there some pics from two weekends ago.

 

[GUNGUY-TC]

More demo and frame extentions

Still some demo to go however after I started cutting got the deal of the year on a trailer in TX so I had to step things up.

 

[GUNGUY-TC]

Make it so it can tow

I got it back together enough to go pick up the trailer

 

[Bob86ZZ4]

Looks good! Thanks for joining and posting. I have almost no fabrication skills so I love seeing other people's work.

 

[bushpilot-TC]

love the steps! Welcome!

 

[Bob86ZZ4]

I've also got no engineering skills. Just wondering about that receiver hitch? Would some lateral members running from the frame rails down to that lower cross bar (where the receiver is mounted) make sense? Provide more support to that lower section? Just seems like that might strengthen that hitch a bit?

 

[GUNGUY-TC]

Thanks for the welcome guys. Still lots to do, the inside is just a box with carpet and walls. I am going gut it and built it all back up.

Next project I'm relocating the generation to the back between the frame rails with a custom fuel cell and storage on the left side and battery trays, invert, shore power set up on the right side. Next few weekends our booked so it will be few weeks.

Here are a few pics of the trailer I picked up and my co-pilot for the TX run.

 

[GUNGUY-TC]

I've also got no engineering skills. Just wondering about that receiver hitch? Would some lateral members running from the frame rails down to that lower cross bar (where the receiver is mounted) make sense? Provide more support to that lower section? Just seems like that might strengthen that hitch a bit?

They are in the plan.

I am closing the back all the way across with a center door and slider set up for the generator and side doors on the right and left where I will put the fuel cell, batteries, and such. When I finish the framing I will add some struts to tie the frame into the lower bumper section. I place to have them split seam of the original frame and extensions and tie them together. I also have some plates we cut to double up the sides of that connection. The deck comes off as a separate piece from the back boxes and extensions. I did temperately weld them for the run to Texas and only used the goose neck set up.

Here is pic of the deck attachments and the well for the ball

 

[samcrimm]

Glad your with us and your rig is looking good, love your pictures too. Post some of your truck house, What size gen are you going to use? And what are you going to do with your rv when your finished? I use mine as a camper and pull a toad. Trying to figure out how to get more stuff on board, enclosed or open 20 to who knows what.
Sam

 

[bushpilot-TC]

welcome!

whats up w/ the light (mounted on the A pillar) next to your co-pilot?

 

[GUNGUY-TC]

welcome!

whats up w/ the light (mounted on the A pillar) next to your co-pilot?

There are four total one at each A pillar and two on the ceiling by the pass through. They have red bulbs so you don't loose you night vision if you need to locate something in the cab at night while driving. They were in the truck when I bought it. I have used them a few time now and they are handy.

 

[bushpilot-TC]

There are four total one at each A pillar and two on the ceiling by the pass through. They have red bulbs so you don't loose you night vision if you need to locate something in the cab at night while driving. They were in the truck when I bought it. I have used them a few time now and they are handy.

makes sense.

ours was built/equipped with similar driver/passenger lighting (over each seat) - one white & one red (separate push to activate lens').

We also have (factory equipped) RED floor lighting which can be activated by a dash switch....Ive converted the floor lighting to RED LED (theyre your typical trailer/marker lights).

I added RED led lighting (along w/ while) under the toe kick in the rear of the coach....so if someone needs to be in "the house" they can turn on the RED lights (at night) and keep from blinding the driver w/ glare reflected off the windshield.

 

[GUNGUY-TC]

I may switch to LEDs the truck is a 2006 however it has some retro 80's feel about it. Kinda like some of it however might be cool to step it up a bit.

 

[bushpilot-TC]

interesting, ours in a 04, but its a Columbia.

 

[GUNGUY-TC]

interesting, ours in a 04, but its a Columbia.

We have owned a couple of FL120's and a FL70 Sport Chassis. Also, had a K600 and K900.

This is our first International. Very happy so far. Only issue was the engine harness was in pretty bad shape so the thing was throwing warning lights left and right $600 for the harness and another $500 for all new sensors and she is right as rain.

 

[GUNGUY-TC]

So I got a few hours in on the rear storage compartments. We have been way to busy at the shop to steal any time on machines during the week so everything has to be done on the weekend for awhile. With the log weekend coming up I hope to get the slides and draws fabricated for the batteries and generator. Then I can work on the wiring and plumbing at the shop at the house.

 

[bushpilot-TC]

that would/will make some nice pass thru storage - Then I could fit my 25 ft (telescoping) flag pole in that

 

[GUNGUY-TC]

that would/will make some nice pass thru storage - Then I could fit my 25 ft (telescoping) flag pole in that

This one won't be a pass through. I will have 12' long boxes down both side with partial a pass through in front. Going to work on her over the weekend, hope its not too hot.