replacement

I have an old circuit board # 3104757.004 that I was advised by Dometic to replace with 3316230.700 board. My old board has a 12v transformer. 1st question- Is the only way to get 12v to new board is run a new line? If so, please suggest where from. 2nd question- I do not have a plug so I'm...

Hey All, Having a tough time on which replacement to purchase here. Looks like my original blower motor was a FASCO 231916. I can't seem to locate any replacements and as far as compatibility goes - don't see any verbiage anywhere online like "Compatible with" like you typically do on stuff...

Greetings from the Great White North, We had a lino floor split over the winter in our 2014 Greywolf and decided to replace it with vinyl planking. There is a carpeted box under the sink/range that skimmed very closely over the lino but appears to be too snug to clear the planking. I can't see...

Hello, Sorry if this has been answered already (searched and did not find or see an answer), but my wife and I just purchased the subject travel trailer today. We were told the RV did not come with a remote for the awning LED lights. Does anyone know a compatible remote that would work for...

I'm trying to order a new water filter for my 2013 GT329DS , and I'm not sure what to order as this is the first time I've changed it. So far I can say that I have a Pentair Pentek 10" Slim Line Filtration System #158196. The filter that I removed has 16330 etched on the top, but no other...

The tail light seals on my 3050s are deteriorated and I can't make out the brand/park number anymore. Does anyone have a part number or link to replacement seals? Thanks!

Where can I get replacement blinds for my 2021 Sabre 38dbq?

I have a 2021 Cedar Creek 311RL that has a leaking left rear leveling jack. My plan is to remove and repair. If I can't get it repaired soon or not at all, I'd like to have a replacement located if needed. Would anyone have the model or part number for the Lippert jack? I have been looking...

Anyone know how to get a replacement for the remote for jacks, awnings and slide outs on 2011 Silverback Alta system AS-1000 ML Thanks

I need a new 100a converter. I wanted a progressive dynamic but it seems they only go to 80a. What would be the next brand choice?

Our "new" A213HW camper has a couple of exposed corners on the inner edge of the upper/lower door halves. Looks like the little rubber corner protectors either came off or were never put on. I have searched a bit on line but haven't been able to find exact matches.:crying: Wife caught and...

I need to replace an inside wall panel following a leak. Any idea how to find a panel identical to the original?

We are fixing to replace the main awning on our 2008 378XL. Anyone have any advice? It doesn't look like a simple swap-out. It looks like a bracket on the roof has to be removed in order for the awning to slide in and out from the front end cap area. Our awning is the Dometic A&E WeatherPro...

Two side exit windows broke on the Dempster Highway due to trucks going the other way and not slowing down, I removed the windows to expose the model sticker and unable to find anything based on the numbers on the sticker. I'm attaching a photo of the sticker. The trailer is 2023 Wolf Pup...

Hey all, I'm about at my wits end trying to solve this problem. Our 2018 Rockwood Ultra Light 2304DS fridge has died. I know it's the cooling unit because we had a very distinct ammonia smell when it failed. It won't run on gas or shore power, it's dead. I try to look at these occurrences as...

This video shows the type of gasket used on my 2006. Has anyone replaced their gaskets? Any advice?

I have a 2016 Berkshire 38A. I was putting out the dinette slide when I heard a bang. There is a double sprocket that connects two chains: one from the back of the slide and one from the front of the slide. The top sprocket has several teeth missing. Where can I find a replacement for this part...

I have an electric awning which has a light strip in the roller. The awning needs to be replaced which normally would not be that hard to do. However, this awning has the wires for the light in the fabric along the edge. Does anyone know how I would find a replacement or how to replace using the...

Hey there, We have a 26tbud, 12 yrs old so some of the cushion cover seams are letting go. There’s no finishing of seams! Anybody know where we could get the fabric? I have labels and fabric names. Just need a source. Tag says mastecraft. Thanks! Heidi

Hello fellow FROG peeps!!!! With regards to my 2014 Georgetown XL 378 TS I have a “cable route” question . Installing an aftermarket back-up camera system, it is a wired system, all the new camera cables are 4 pin and the old system is all 6 pin The 2 side cameras are easy, but trying to to...

I have a 2015 Legacy 360RB. There are four house batteries but I can't read any information on them to know what I should replace them with. I assume they are 6V golf cart type batteries. Can anyone help me?

last year, i snapped my kitchen faucet. The plastic post that holds it in snapped in the center. this year, we decided to hook the water up. knowing the valves were off, We hooked up the water and testedthe 2 other sinks as well as cleaning the lines. All was well for about 20mins, and then the...

Greetings, We have a 2018 Forester 2291S MH on a Ford chassis. Currently the 12vdc power comes from 2 group 27MDP batteries in the steps and are showing signs of old age (aren't we all). I want to go with AGM so that I don't have to water the batteries(no $$ for Lithium) and I need some input to...

I had a slam latch that would not budge (tried all the lube/etc, and it was just locked up, key would not even turn it slightly). So.. I ended up having to force it open (the ole flat head screwdriver in the key hole and twist method. That worked, but the lock is clearly dead now. Does anyone...

I have a FR3 32DS 2016 the bathroom floor is getting soft and squishy other than that there is no sign of leakage. Now has anyone cut out old floor and replaced with preasure treated plywood. is the a blue print for the cross member /frame locations ?