hydraulic

I belive that a lot of my problems are due to air in the hydraulic system. How do you remove air from the system. :confused:

I'm having some issues with my leveling jacks on our 2004 Georgetown 359TS and I have hit a couple of walls in my troubleshooting that I could use some help with: 1. Where is the hydraulic fluid reservoir? 2. Were are the circuit brakers and/or fuses for the jacks This past weekend I...

howdy all: I had all orange hoses replaced last summer and everything ran fine until 2 weeks ago and on my 2012 378xl the cylinder that drives the slide out was leaking, so the guy that replaced my hoses ordered a new lipert cylinder and he installed, so this Is where it gets weird all was fine...

I have a 2014 Silverback 29ik. We have the lippert hydraulic landing gear /jacks. They both seem to work fine operate in both directions ok. No fluid leaks. Simple retract and extend switch, no blown fuses. My issue is as follows: Park 5er on relatively flat brick paver or concrete pad...

Hi folks, Reposting since I didn't get a response in the Georgetown forum. I just finished running new hydraulic lines, replacing a bad hydraulic cylinder and replacing all the seals on the my leaking pump. All went good until I tried to re-prime the pump. Motor is running but I can't get it...

Just finished running new hydraulic lines, replacing a bad hydraulic cylinder and replacing all the seals on the leaking pump. All went good until trying to re-prime the pump. Motor is running but I can't get it to draw any fluid. Tried running it for 20 seconds and letting it cool for a while...

I had a new pump put in my fifth wheel trailer and it worked fine for a while and then last year I could not get to retract so i took the lines lose at the pump and pushed it in manually . I now realize that i did not tighten the lines and when I took it out this year the slide out would not...

I have a CC 38RD, I need to fill the hydraulic tank, but the tank is so close to the top of the compartment that a funnel will not work. Any ideas out there other then some sort of pump, which I don't have. Thanks RC :confused:

Anyone know the model number of the Lippert Components, Inc. (LCI) electronic/hydraulic leveling and slideout system used in the 2009 Georgetown 350 (bunk slide out model)? I have inserted a picture of my eternally leaky but completely functional unit. Back in 2010 the dealer tried to stop the...

Lately I have noticed a grinding noise associated with a considerable delay In movement when extending or retracting the main living room slide on our 2009 379xl. After some thorough research and observation I came to the conclusion that the noise I was hearing is the threads of the hydraulic...

Hi We bought a Flagstaff Aframe popup last week and today discovered the power hydraulics to open the top are not working. We are plugged into electric and all is working inside but lift doesn't work. Anyone have similar issue please. We are newbies so really appreciate any insights.

Wanted to add hydraulic fluid for our SB 31RK and the spacing is so tight and well after leaving quarter of the bottle spilled all over the place. How does everyone fo it? Used 2 diff. Type siphon type but angle is tough

We are looking to buy our first MH after years of pop up and tent camping. We were looking at Georgetowns on line. Specifically the 310 DS. From what I've seen it looks like both the LP tank and hydraulics are just sort of hanging in the breeze. Is it just me or does that not seem like the...

What kind of Hydraulic fluid is used in the leveling system found on our FR3's. What weight? JeNNY (2015 FR3 / 30DS) 2000 Jeep TJ Moab Rock Crawler 2013 Jeep JK

so a very bad day, everything went wrong. pulled slide in, door cabinet was just a bit jarred and the slide (opposing) hit it and the cab door got jammed on it. finally able to remove the busted part of the cab door. seems like there is gap now slight but there. I can slide a weed...

Not sure if this is just a temperature issue but our Sierra has four slides and not all the time but randomly the forth slide will stop coming in. We wait 5 seconds then it will restart. It sounds like something trips near the resevoir. If is was a temperature issure I would suspect none of the...

I have a 2014 FR3 30DS and was wondering if anyone knew how to raise and lower the hydraulic jacks manually

2008 Georgetown SE 350: I'm having trouble locating the hydraulic reservoir for the slides and jacks.

2008 Georgetown SE 350. Does anyone know where the hydraulic system reservoir is located? Thanks.

2008 Georgetown SE. Hydraulic slides and levelers. 2 slides. My wife open the main slide without leveling first. The house batteries are new, but were nearly dead. I charged them last night with an external charger. The bedroom slide won't move and the main slide won't retract. Reset the 90A...

Our new 38CK is still on lot with dealer. We were showing our friends how the 6 point hydraulic leveling worked. It level fine then we went to put the legs back up and nothing. What do you do if your in a camp area and you can't retract your legs to leave?

I getting ready to go south for the winter with my Wildcat. I have 3 hydraulic slides that I have concern for using it during the extreme cold. We are packing up at below zero and need to open and close daily so the snow doesn't interfere the closing. Will the hydraulic oil get to heavy in the...

Good day all, I'm a new member--just got a 2015 Cedar Creek Silverback fifth wheel! :thumbsup: I live in an area with heavy industrial fallout. My coach will be stored in a covered farm implement barn with open sides, subject to lots of dust due to tractors and trucks moving around. So at...

So while I was underneath my slide out (door side) lubricating the slide seals, I noticed that there was a gap in the adjusting nuts on the hydraulic ram that pushes/retracts the slide. The threads are clean with no rust were the gap is. How does this get loose? There is nylon locknut on the...

Because of the rear slideout the 24R does not have a latch to hold the rear compartment door open. I'm think of adding a small Hydraulic Lift Support Arm. Has anyone done that? If so, what size did you use? Thanks, Jim