Frankenstein

Weldman

Senior Member
Joined
Jun 17, 2019
Messages
119
Location
MC
1986 International S1954 236 inch wheel base beverage truck 28,0000 GVW with DT466 engine Spicer 5 speed transmission with split rear axle bought for $750. Transmission was trashed beyond repair is reason for truck so cheap so I tossed it and put a Eaton 6 speed in it lengthened drive shaft made new drive line brackets. Tossed the bench seat and put in air seats from junk yard, chopped the shifter that came with transmission down. Next I chopped the beverage truck body in half taking the top half off, welded a pedestal in the bottom half to hold a camper. Replaced all the wiring from cab back to accept 7 wire trailer pin and for the new LED tail lights I put in. Took bumper off or whatever that was on rear and replaced it with a 3/4 inch plate bent to fit the frame and bolted in after drilling holes for it. Took the roll up doors out and welded in steel doors that open outward to access below the pedestal in the back.


Now for the camper that sits on top of all this is...


1968 Fiber-Top built by Lynnwood Fiberglass in Lynnwood Washington, only 3 were built and I have only one left as I far as I know. Technically I'm 3rd owner as the story goes, the first owner was going to chop it up and throw it away till his neighbor took possession of it before he could. They used it for few decades and decided to sell it after hitting old age, someone they knew bought it from them but never went and picked it up out of their yard. Fast forward 5 years later the city of Edmonds WA came in and said register it, sell it or dispose of it so the person who bought it was contacted and he posted it on Craigslist and is where I found it by accident cause by then I have gave up and was going to build my own truck camper. Bought it for $500 and is titled and registered which is rare for something so old. According to history one of the three that was built was destroyed when it flew off the back of a truck and shattered across the interstate.

So without further delay here is the pictures...
 

Attachments

  • 0802181849a.jpg
    0802181849a.jpg
    113.7 KB · Views: 21
  • 0802181848a.jpg
    0802181848a.jpg
    103 KB · Views: 24
  • KIMG0043.jpg
    KIMG0043.jpg
    61.9 KB · Views: 17
  • KIMG0041.jpg
    KIMG0041.jpg
    97.2 KB · Views: 21
Pictures...

Priming it... This almost caused a few wrecks since I lived on a main street in the city at the time of this and sure caused people to stop and look too. Even the city code enforcer loved it so much he paid me a visit to tell me I need to move it.
 

Attachments

  • IMG_20180928_182748.jpg
    IMG_20180928_182748.jpg
    28.9 KB · Views: 18
  • IMG_20180928_182815.jpg
    IMG_20180928_182815.jpg
    33.6 KB · Views: 19
Guess I need to up the ante in here, here is some more pictures...
 

Attachments

  • IMG_20190214_172536.jpg
    IMG_20190214_172536.jpg
    109.1 KB · Views: 19
  • KIMG0099.jpg
    KIMG0099.jpg
    99.8 KB · Views: 22
  • KIMG0356.jpg
    KIMG0356.jpg
    87.7 KB · Views: 17
Rain or shine or snow it go's...
 

Attachments

  • KIMG0394.jpg
    KIMG0394.jpg
    53.8 KB · Views: 12
  • KIMG0398.jpg
    KIMG0398.jpg
    86.9 KB · Views: 17
  • KIMG0403.jpg
    KIMG0403.jpg
    92.9 KB · Views: 21
  • KIMG0393.jpg
    KIMG0393.jpg
    63.3 KB · Views: 15
Houston we have a landing...
 

Attachments

  • IMG_20190221_163532.jpg
    IMG_20190221_163532.jpg
    36.4 KB · Views: 20
  • IMG_20190311_180901_01.jpg
    IMG_20190311_180901_01.jpg
    96.9 KB · Views: 23
  • IMG_20190307_073007.jpg
    IMG_20190307_073007.jpg
    127.2 KB · Views: 20
  • KIMG0425.jpg
    KIMG0425.jpg
    116.5 KB · Views: 19
Road trip...

The inside is not complete and still isn't as I type this, had to redesign the interior after I stripped it down to the shell. More pictures of interior in due time.
 

Attachments

  • KIMG0432.jpg
    KIMG0432.jpg
    101.1 KB · Views: 21
  • KIMG0427.jpg
    KIMG0427.jpg
    113.6 KB · Views: 20
Sharp looking outfit there WM! I can appreciate the amount of work you've done. I really like the looks of those 1980s International nose's. It looks as though you hail from Washington? I'm just outside Spokane.
 
Last edited:
I think it's cool. Tons of work. Impossible for a guy like me with almost no skills. Do you flat tow the Subby?
 
Sharp looking outfit there WM! I can appreciate the amount of work you've done. I really like the looks of those 1980s International nose's. It looks as though you hail from Washington? I'm just outside Spokane.
Thanks! Yes it’s a 1986 International S1954
Actually I was passing through south of Spokane though I did live on Olympic Peninsula for few year. I’m originally from Texas and as of now I’m resident of Montana out in Miles City hence the MC. Funny you say hail, just went through hail storm yesterday, what joys.
Be passing through Spokane next month or at least outskirts...
 
Last edited:
I think it's cool. Tons of work. Impossible for a guy like me with almost no skills. Do you flat tow the Subby?
Yep I do, it’s a 5 speed. To get skills just grab whatever you want to do and screw up a few times trying to do it and learn from your mistakes. I never went to trade schools or any college nor did anyone teach me, all self taught. I believe you can do it with time.
 
Time for interior work... Wiping the slate clean and starting over.
 

Attachments

  • IMG_20190204_134413.jpg
    IMG_20190204_134413.jpg
    107.7 KB · Views: 21
  • IMG_20190204_135622.jpg
    IMG_20190204_135622.jpg
    103.1 KB · Views: 20
  • KIMG0479.jpg
    KIMG0479.jpg
    113.9 KB · Views: 21
  • KIMG0480.jpg
    KIMG0480.jpg
    114.5 KB · Views: 18
Wall cavities are little thin for my taste of only one inch thick in depth so time to add more. While I'm at it time to replace the 4x4's that the camper tie downs were bolted to to be replaced. They were so rotted they crumbled in my hands.
 

Attachments

  • KIMG0492.jpg
    KIMG0492.jpg
    117.2 KB · Views: 13
  • KIMG0518.jpg
    KIMG0518.jpg
    120.5 KB · Views: 12
  • KIMG0519.jpg
    KIMG0519.jpg
    111.1 KB · Views: 12
  • KIMG0521.jpg
    KIMG0521.jpg
    91.8 KB · Views: 13
The wood stringers in the floor were rotted to point of crumbling not to mention the million screws used since the previous owner put 5 sheets of plywood down just to make the floor piece alone.
 

Attachments

  • KIMG0405.jpg
    KIMG0405.jpg
    85.7 KB · Views: 11
  • KIMG0410.jpg
    KIMG0410.jpg
    84.3 KB · Views: 13
  • KIMG0507.jpg
    KIMG0507.jpg
    105.8 KB · Views: 12
Added furring strips to increase wall cavity depth to increase R value of insulation in the walls
 

Attachments

  • KIMG0517.jpg
    KIMG0517.jpg
    85.6 KB · Views: 10
  • KIMG0518.jpg
    KIMG0518.jpg
    120.5 KB · Views: 11
  • KIMG0519.jpg
    KIMG0519.jpg
    111.1 KB · Views: 10
On wards to spraying insulation in which ran about $1200 to do myself, could of went polyurethane foam boards but the curvature of the walls don't allow it to be proper seal. Plus wanted to prevent thermal bridging so I'm going with hybrid system of spray in insulation and cellulose fiberglass insulation. The kind you spray in your attic but I am hand picking it apart and fluffing it up then placing it in.

All furring strips were riveted in then glued with PL construction adhesive along with any subflooring.
 

Attachments

  • KIMG0523.jpg
    KIMG0523.jpg
    115.9 KB · Views: 20
  • KIMG0540.jpg
    KIMG0540.jpg
    106.2 KB · Views: 19
  • KIMG0542.jpg
    KIMG0542.jpg
    110.9 KB · Views: 20
  • KIMG0544.jpg
    KIMG0544.jpg
    106 KB · Views: 17
Wow, that's looking super tight! I've done this sort of work a million times, and I can appreciate your involvement. It'll be well worth it in the long run. Will you be living in there, or just RV'ing it?
 

Try RV LIFE Pro Free for 7 Days

  • New Ad-Free experience on this RV LIFE Community.
  • Plan the best RV Safe travel with RV LIFE Trip Wizard.
  • Navigate with our RV Safe GPS mobile app.
  • and much more...
Try RV LIFE Pro Today
Back
Top